Thank you for purchasing a system ISCHELL. We are delighted to welcome you to the growing number of world-renowned music, technician, audio engineers and artist users who have chosen to use our systems.

We are at your disposal and we will always remain so over time, for any question relating to the use of our systems on your instrument. Your complete satisfaction is a priority for us. Consult the online help and contact us if necessary.

  • The model 2X48CC is a system that operates on phantom power. It is equipped with the new type of contact microphone developed by the brand ISCHELL in 2008, in order to reproduce with the greatest fidelity the acoustics of your instrument, the attack, the timbre, the woody color, your playing and your playing nuances, without the problems of feedback and the resumption of surrounding sounds (Repisse ). Our hybrid Air / Contact technology works without a filter between the membrane and the soundboard of your instrument. We thus reproduce on a reduced and isolated scale an ultimate aerial sound recording, controlled by the immediate environment of our specific putty audio adhesive. A revolution in the amplification of many instruments on stage, an innovation ISCHELL !
  • All our products are manufactured and assembled in France by hand, with awareness and respect for a job well done, only with high quality components, for products that we hope will bring you satisfaction for many years on stage, in the studio and at each of your performances amplified.
  • We strongly recommend that you take a few minutes to read this manual. Indeed, it is important to respect a few principles in order to benefit simply and quickly from these new systems.

What you need to know

  • Always unplug your instrument before attempting placement again or changing the low cut.
  • Wash your hands before kneading the putty and carefully clean the bonding areas before doing your tests, they must be clean, dry, non-greasy and smooth.
  • Reform the putty adhesive roll of the contact microphone as shown at each test and youUse only the audio adhesive putty ISCHELL !
  • This system operates on phantom power from 9v to 48v.
  • Operate gently to act on the low cut. A small pointed object is needed to operate the switches.
  • Your system is delivered to you with the low cut positioned on 360Hz. We recommend to research the placement of the microphone on this position. If after determining the best location, you find the sound lacks bass, then set the low cut to 180Hz. If you find that the sound still lacks depth, try the Flat position.
  • You have two types of audio adhesive putty for the contact microphone. A white and a gray, they do not have the same sound. The white putty has a clear sound, use it to start your tests, if after having defined the best placement for the microphone, the sound remains too bright, then try the gray for a duller sound in the highs and rounder in the highs. bass. The gray putty is particularly suited to shiny instruments as well as quartet instruments.
  • This system is like your instrument, it is fragile. Never pull on the cables, always remove the contact microphone delicately from your instrument, taking it by the shell and gently tilting it while removing the putty to avoid a too sudden suction effect (fragile membrane) and to preserve the surface of the instrument.

Low cut


  • Unscrew the cover. Optionally plug in a female XLR cable to help maintain the connection while you unscrew the cover.
  • A small switch is located inside allowing three 180Hz / 360Hz / Flat positions.
  • The two switches on the left cut the bass below 360Hz (maximum cutoff).
  • To have all the bandwidth (Flat), push the bottom switch to the right (the top one stays on the left).
  • The 180Hz position is obtained by putting the top switch on the right (the bottom one remains on the left).
  • A drawing represents these positions on the hull of the XLR.

Choice of adhesive putty for the C1 Original:

  • Your system is delivered to you with 2 doses of adhesive putty, one white and one gray, they do not have the same sound.
  • The white putty has a linear sound and rather bright in the highs, this is the one you should use by default for your testing.
  • The gray putty sounds rounder in the bass and duller in the treble. When the sound remains too bright with the white putty, try with the gray putty in the same spot. Suitable for very shiny instruments and sometimes for quartet, double bass, violin ...
  • We recommend that you start testing with the white putty. If after determining the best position the sound remains too bright or lacks roundness, then try with the gray putty in the same spot.

Preparation of the C1 Original contact microphone

  • Knead and stretch a portion of the supplied putty audio adhesive for at least 30 seconds to heat it up and make it stickier.
  • If it is less than 18 ° in your room, you can possibly warm it slightly by bringing it near a source of gentle heat.
  • Then make a regular roll 6cm long and 6mm in diameter.
  • Then place it around the edge of the microphone provided for this purpose, taking care to connect the two ends of the roll well by covering them, then release the central part without crushing it
  • The place chosen for installation must be clean and dry, degreased if necessary.
  • Put the microphone down then press it lightly, it should not touch the instrument, approximately 2 / 3mm.
  • Then seal the putty all around the mic to make the middle part of the mic airtight.
  • Then place a cable clip 3/4 cm with a little putty to avoid picking up noise by the cable.
  • If during the first tests a sharp feedback is heard, it means that the seal has not been respected, press the putty all around the microphone again.
  • If you find that the tonal balance is good but the sound is not homogeneous in its dynamics (volume of the notes) or harmonics, lightly press the microphone again, this will compress the sound and may correct these problems. If possible, use the adjustable shim provided. See below.
  • If you think you have compressed your sound too much, you can, without removing the microphone, try to pinch it to make it go up a bit. Attention, all these manipulations must be unplugged microphone.
  • Important: Only use the audio adhesive putty ISCHELL, any other putty will distort the sound.

Compression control

You can use the included adjustable compression shim to control the pressure on the mic. Indeed, the pressure on the microphone acts as an audio compressor, the more you push it into the adhesive putty, the more you compress the output sound, so you will have less level but a more stable sound in its dynamics. Can also correct harmonics that would be redundant on a violin, folk guitar ...

  • Place the microphone where you want it and lightly press it down.
  • Adjust the level of compression by turning the knob on the cleat.
  • Place the wedge on the microphone and press until it touches the surface of the instrument.
  • Wait a few seconds, remove the wedge then seal the putty all around the microphone to ensure a seal.
  • Try the instrument.
  • Increase the compression level if necessary by repeating this operation. 
  • The average compression point is located between the 5th and 7th point on the cleat, starting from the smallest.
  • Can be used to know the compression of your microphone if you need to remove it in order to reproduce it. Place the wedge on the microphone and then turn the knob until you feel you touch the microphone. Note the value of the button in order to reproduce this depression during the next pose.


  • Model 2X48CC
  • XLR integrated preamp
  • Independent XLR outputs
  • Works on phantom power from 9v to 48v
  • High pass three positions: 360Hz, 180Hz, Flat
  • Dual contact microphone kit
  • Condenser microphones
  • Two C1 contact microphones, bandwidth: 40 / 16000Hz
  • Active electronics
  • audio adhesive putty for contact microphones provided
  • Cable lengths depending on the instrument, 45 - 65 - 100cm
  • Double-sided or Velcro Velcro attachment to the instrument
  • Microphone kit weight: 100 grams
  • Made in France

After-Sales Service

  • Our products are guaranteed against any manufacturing defect for 2 years from the date of purchase.
  • We are at your disposal and we will always remain so in time for any question relating to the use of our systems on your instrument.
  • Your complete satisfaction is a priority for us. Consult the online help and contact us if you cannot find the solution to your problem.
  • Refer to the CGV on for more information on the warranty.


ISCHELL MICROPHONES  119 impasse de la gare – 44800 Saint-Herblain – FRANCE

Tel: +33 (0)6 62 09 54 91 – Email:

Leave comments

Your email address will not be published. Required fields are marked with *